XF100-400mmF4.5-5.6 R LM OIS WR Firmware update
Last Updated: 04.27.2023
Please read this update after refreshing this page.
- In case of Windows (Internet Explorer / FireFox / Google Chrome), hold down the “Control” key and “F5” key.
- In case of Mac (Safari / Google Chrome), hold down the “Command” key and “R” key.
- In case of Mac (FireFox), hold down the “Command”, “Shift” and “R” keys at same time.
The firmware upgrade is not required if its version is latest.
- Refer to “2) Firmware version checking procedure” in the “Detail of firmware update steps” below to check the firmware version.
Please use your camera and lens with the latest version of firmware.
- If you don’t use them with the latest version, you may not enjoy their full performance. Check the latest firmware version from the link below.
Detail of the firmware update
The firmware update Ver.1.30 from Ver.1.21 incorporates the following issues:
Aperture control parameters have been optimized to improve exposure tracking during movie taking.
Focusing motor noise variation during movie taking has been stabilized.
Focus tracking at zooming operation has been improved during movie taking.
This enhancement No.3 requires the following cameras with latest firmware versions. Please make sure to upgrade camera firmware to the latest version before upgrading the lens firmware.
Link to the camera list
X-H2S (Ver.1.00 or later), X-H2 (Ver.1.00 or later), X-T5 (Ver.1.00 or later), X-T4 (Ver.1.60 or later), X-T3 (Ver.4.40 or later), X-S10 (Ver.2.50 or later)
The firmware update Ver.1.21 from Ver.1.20 incorporates the following issue:
Fix of minor bugs.
The firmware update Ver.1.20 from Ver.1.11 incorporates the following issue:
Compatibility with FUJINON TELECONVERTER XF1.4X TC F2 WR (bundled with XF200mmF2 R LM OIS WR) is added.
The firmware update Ver.1.11 from Ver.1.01 and Ver.1.10 incorporates the following issues:
The lenses will deliver superior performance in combination with FUJINON Tele Converter XF 2X TC WR.
*The firmware Ver.1.10 or later of XF100-400mmF4.5-5.6 R LM OIS WR should be installed.
*The firmware upgrade of the lenses should be conducted after the upgrade of camera’s firmware upgrade.
The accuracy of Manual focus adjustment will be enhanced when using one with cameras below.
X-E1 / X-E2 / X-E2S / X-Pro1 / X-Pro2 / X-T1 / X-T10
It is necessary to upgrade the firmware of cameras above at the same time.
The firmware update Ver.1.01 from Ver.1.00 incorporates the following issues:
AF tracking performance on AF-C and Movie mode will be improved when they are attached to FUJIFILM X-Pro1or X-E1.
Firmware Update Steps
- Check the firmware version.
- Prepare a formatted memory card.
- Download the firmware and copy it to the card.
- Put the memory card with the firmware in the camera and update it.
If firmware updating fails, the camera may no longer operate correctly in some cases. Carefully read the notes provided here*Always use the fully-charged battery when updating the firmware as a basic manner. Never turn the camera off or attempt to use any of the camera controls while the firmware is being overwritten.
- You can update the firmware from old version directly to the latest one.
- Firmware updating requires approximately 5 minutes.(maximum)
- Once the firmware has been updated, some data of the previous version cannot be restored.
- Please check here if you encounter any problems.
Please read this Agreement carefully before downloading this upgraded version software (“FIRMWARE”). By downloading FIRMWARE, you are agreeing to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, you are not authorized to download FIRMWARE.
Article 1. License
FIRMWARE is the upgraded version of software that FUJIFILM Corporation. (“FUJI”) already distributed to you included with FUJI’s product(s) (“ORIGINAL FIRMWARE”). All copyrights and other proprietary rights to FIRMWARE are retained by FUJI, and nothing contained herein shall be construed, expressly or implicitly, as transferring or granting to you any right, license, or title unless otherwise explicitly granted under this Agreement.
Article 2. NO Warranty
FUJI EXPRESSLY DISCLAIMS ANY WARRANTY FOR SOFTWARE. SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL FUJI BE LIABLE FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES RESULTING FROM THE USE OF OR INABILITY TO USE SOFTWARE.
Article 3. Restrictions
You shall not, or shall not have any third party, reverse-engineer, decompile, or disassemble FIRMWARE.
*Make sure there isn’t any file with the same name in the destination of the firmware to save. If there is a file with the same name, the browser may automatically alter the name of the firmware like the name and (1). A camera will not recognize the firmware correctly with an altered name like that.