This website uses cookies. By using the site you are agreeing to our Privacy Policy.

X100 Firmware update

Version: 2.11

Last Updated: 10.29.2015

Overview

Notes

Please read this update after refreshing this page.

  • In case of Windows (Internet Explorer / FireFox / Google Chrome), hold down the “Control” key and “F5” key.
  • In case of Mac (Safari / Google Chrome), hold down the “Command” key and “R” key.
  • In case of Mac (FireFox), hold down the “Command”, “Shift” and “R” keys at same time.

The firmware upgrade is not required if its version is latest.

  • Refer to “2) Firmware version checking procedure” in the “Detail of firmware update steps” below to check the firmware version.

Please use your camera and lens with the latest version of firmware.

  • If you don’t use them with the latest version, you may not enjoy their full performance. Check the latest firmware version from the link below.

Firmware

Detail of the firmware update

Ver.2.11

The firmware update Ver.2.11 from Ver.2.10 incorporates the following issues:

Support for Windows10

The phenomenon is fixed that images in a camera cannot be transferred to a Windows10 PC via a USB cable.

Ver.2.10

The firmware update Ver.2.10 from ver.2.01 incorporates the following issue:

Addition of the function for TELE CONVERSION LENS TCL-X100

1)Change of shooting menu
Current : WIDE CONVERSION LENS > ON / OFF
New : CONVERSION LENS >WIDE / TELE / OFF

2)When “TELE” is selected in the “CONVERSION LENS” menu, the size of the Bright frame in the Optical Viewfinder will switch to shooting area for the TELE CONVERSION LENS.

<Note>
With this upgrade of X100, settings including date will return to default.

Ver.2.01

The firmware update Ver.2.01 from ver.2.00 incorporates the following issue:

The phenomenon is fixed that in Manual Focus mode, repeated pressing the shutter button halfway or repeated recording images could move focus position and the distance indicator to near side.

Improvement of AF speed

Approximately 20% faster AF speed is achieved in various conditions such as bright scenes, dark scenes and changed focus distance compared to the previous firmware version.

Ver.2.00

The firmware update Ver.2.00 from ver.1.30 incorporates the following issues:

Improvement of close-up focus performance

The focus distance from the lens surface without switching to macro mode is approximately 30% shorter compared to previous firmware version.

Ver.1.30

The firmware update Ver.1.30 from ver1.21 incorporates the following issues:

For operation of newly added functions, which are described as following item 1, please download PDF data issued as “X100 New Feature Guide”.
Please check them in detail. (PDF: 635KB)

"Focus Peak Highlight" function for manual focusing is added.

The function, which features on FUJIFILM X100S and X20, is added and assists accurate and sensitive manual focusing by enhancing the outline of your subject in high contrast.
* With this update, “Focus Peak Highlight” function is selected as a default setting. Pressing the center of the command dial for a while enables you to switch the setting of “Focus Peak Highlight” and “STANDARD” (off of “Focus Peak Highlight”). And “MF ASSIST” is added in SHOOTING MENU where you can select “HIGH” and “LOW” in “Focus Peak Highlight” and “STANDARD”.

Ver.1.21

The firmware update Ver.1.21 from ver1.20 incorporates the following issues:

Improved manual focus operation

This makes it easier to capture the peak of the focus by displaying the image with shallow depth of field, using open aperture, when adjusting the focus with the electronic view finder or the LCD.

Ver.1.20

The firmware update Ver.1.20 incorporates the following issues.

After updating into this version of the firmware, some new functions will be added and further improvements will be observed. Those are shown as “Improved items” below.
For operation of newly added functions, which are described as following item 1 to 6, please download PDF data issued as “FinePix X100 New Feature Guide”.
Please check them in detail.

Faster start-up time

The camera start-up time is shortened by approximately 0.2 second with QUICK START mode OFF.

Ver.1.12 / 1.13

The firmware update Ver.1.12 / 1.13 incorporates the following issues:

Improved operability of selecting focus area

Previously, the focus area was selected while holding the AF button on the back. With the upgraded firmware, pressing the AF button will switch to the focus area selection screen and the area of your choice can then be selected.

Ver.1.11

The firmware update Ver.1.11 incorporates the following issues.

The phenomenon is fixed that a camera will automatically turn off during "Bulb (B)" shooting with the "CONTINUOUS" setting in "IMAGE DISP."

Ver.1.10

The firmware update Ver.1.10 incorporates the following issues.
The contents of the owner’s manual will be partly changed along with this update.

Please check them in detail.

New function for the WIDE CONVERSION LENS WCL-X100 is added to the shooting menu. The function for the WCL-X100 can also be allocated to "Fn/RAW" button.

ver.1.01

The firmware up date ver.1.01 incorporates the improvement against inadequate operation shown in the following.

Hold the "AE/AF LOCK" when changing to OVF after one of 25 focus points(inner portion of 49 focus points) is selected in EVF or LCD.

<Notice>
“AE/AF LOCK” will be canceled when changing to OVF after one of 25 focus points (outer portion of 49 focus points) is selected in EVF or LCD. In this case, you need to use EVF or LCD to hold the “AE/AF LOCK”.

Firmware Update Steps

  1. Check the firmware version.
  2. Prepare a formatted memory card.
  3. Download the firmware and copy it to the card.
  4. Put the memory card with the firmware in the camera and update it.
Detail of firmware update steps

Precaution

If firmware updating fails, the camera may no longer operate correctly in some cases. Carefully read the notes provided here*Always use the fully-charged battery when updating the firmware as a basic manner. Never turn the camera off or attempt to use any of the camera controls while the firmware is being overwritten.

  • You can update the firmware from old version directly to the latest one.
  • Firmware updating requires approximately 90 seconds.
  • Once the firmware has been updated, some data of the previous version cannot be restored.
  • Please check here if you encounter any problems.

Error messages and responses

Download

License Agreement

Please read this Agreement carefully before downloading this upgraded version software (“FIRMWARE”). By downloading FIRMWARE, you are agreeing to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, you are not authorized to download FIRMWARE.

Article 1. License

FIRMWARE is the upgraded version of software that FUJIFILM Corporation. (“FUJI”) already distributed to you included with FUJI’s product(s) (“ORIGINAL FIRMWARE”). All copyrights and other proprietary rights to FIRMWARE are retained by FUJI, and nothing contained herein shall be construed, expressly or implicitly, as transferring or granting to you any right, license, or title unless otherwise explicitly granted under this Agreement.

Article 2. NO Warranty

FUJI EXPRESSLY DISCLAIMS ANY WARRANTY FOR SOFTWARE. SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL FUJI BE LIABLE FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES RESULTING FROM THE USE OF OR INABILITY TO USE SOFTWARE.

Article 3. Restrictions

You shall not, or shall not have any third party, reverse-engineer, decompile, or disassemble FIRMWARE.

DownloadFile name: FPUPDATE.DAT

Caution

*Make sure there isn’t any file with the same name in the destination of the firmware to save. If there is a file with the same name, the browser may automatically alter the name of the firmware like the name and (1). A camera will not recognize the firmware correctly with an altered name like that.