This website uses cookies. By using the site you are agreeing to our Privacy Policy.

X-T30 Firmware update

Version: 1.20

Last Updated: 03.26.2020

Overview

Notes

Please read this update after refreshing this page.

  • In case of Windows (Internet Explorer / FireFox / Google Chrome), hold down the “Control” key and “F5” key.
  • In case of Mac (Safari / Google Chrome), hold down the “Command” key and “R” key.
  • In case of Mac (FireFox), hold down the “Command”, “Shift” and “R” keys at same time.

The firmware upgrade is not required if its version is latest.

  • Refer to “2) Firmware version checking procedure” in the “Detail of firmware update steps” below to check the firmware version.

Please use your camera and lens with the latest version of firmware.

  • If you don’t use them with the latest version, you may not enjoy their full performance. Check the latest firmware version from the link below.

Firmware

Detail of the firmware update

Ver.1.20

The firmware update Ver.1.20 from Ver.1.10 incorporates the following issues:

Regarding the details of No.1, download the “X-T30 New Features Guide” from our website.

New Features Guide: English, Français, Deutch, Español, Italiano, Nederland, Polski, Svenska, Norsk, Dansk, Pусский, Suomi, 中文简, 中文繁體, 한국어, ภาษาไทย, Arabic

Gimbal / Drone support (*)

This firmware adds the following function to complement the current support for still image shooting via USB communications:  
・Starting and ending video recording  
・Adjusting exposure settings (exposure mode, shutter speed, aperture, ISO sensitivity, exposure compensation) for video recording  
・Making manual focus adjustments for video recording
*This is the function via USB communication. About supported gimbals and drones, refer to support information not only on our website but also manufacturers’ websites.

Enhanced autofocus.

*Improving the tracking performance of the eye AF frame, making it easier to attain accurate autofocus on the eyes.
*Improving face-detection performance when there are faces of different sizes within the same frame, making it easier to attain accurate autofocus.
*Improving autofocus capability on a foreground subject even when there is a mixture of foreground and background subjects within a AF frame, causing the foreground subject to go out of focus, e.g. when shooting flowers against a busy background.

Capability to save up to 9,999 pictures in each folder.

Until now, the number of pictures that can be saved in a folder on an SD card was limited to 999. This update will raise the limit by ten times to 9,999 pictures.

Fix of minor bugs.

Ver.1.10

The firmware update Ver.1.10 from Ver.1.01 incorporates the following issues:

Improvement of Q (quick menu) button operability

To avoid accidentally pressing the Q (quick) menu, the button has changed to one of Fn(function) buttons. This will allow customers to disable the Q button function and also to allocate the Q (quick) menu to a different Fn button.

Fix of minor bugs

<Note>
Regarding the method and explanation of the operation, refer to the Q(quick menu) button in the Owner’s Manual.

Owner’s Manual: English, 中文简体, Other

Ver.1.01

The firmware update Ver.1.01 from Ver.1.00 incorporates the following issue:

Improved operability of the Q (quick menu) button

To avoid accidentally opening the Q (quick) menu, the button reaction time has been increased.

*FUJIFILM Corporation plans an additional firmware update in June. This will allow customers to use the Q button as a Fn button. This planned update also allows the user to disable the Q button and adds it as a choice in the Function (Fn) Settings enabling the option to assign it to a different Fn button.

Firmware Update Steps

  1. Check the firmware version.
  2. Prepare a formatted memory card.
  3. Download the firmware and copy it to the card.
  4. Put the memory card with the firmware in the camera and update it.
Detail of firmware update steps

Precaution

If firmware updating fails, the camera may no longer operate correctly in some cases. Carefully read the notes provided here*Always use the fully-charged battery when updating the firmware as a basic manner. Never turn the camera off or attempt to use any of the camera controls while the firmware is being overwritten.

  • You can update the firmware from old version directly to the latest one.
  • Firmware updating requires approximately 90 seconds.
  • Once the firmware has been updated, some data of the previous version cannot be restored.
  • Please check here if you encounter any problems.

Error messages and responses

Download

License Agreement

Please read this Agreement carefully before downloading this upgraded version software (“FIRMWARE”). By downloading FIRMWARE, you are agreeing to be bound by the terms of this Agreement. If you do not agree to the terms of this Agreement, you are not authorized to download FIRMWARE.

Article 1. License

FIRMWARE is the upgraded version of software that FUJIFILM Corporation. (“FUJI”) already distributed to you included with FUJI’s product(s) (“ORIGINAL FIRMWARE”). All copyrights and other proprietary rights to FIRMWARE are retained by FUJI, and nothing contained herein shall be construed, expressly or implicitly, as transferring or granting to you any right, license, or title unless otherwise explicitly granted under this Agreement.

Article 2. NO Warranty

FUJI EXPRESSLY DISCLAIMS ANY WARRANTY FOR SOFTWARE. SOFTWARE IS PROVIDED “AS IS” WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, OR NON-INFRINGEMENT OF COPYRIGHT, PATENT, TRADE SECRET, OR ANY OTHER PROPRIETARY RIGHTS OF ANY THIRD PARTY. IN NO EVENT SHALL FUJI BE LIABLE FOR ANY GENERAL, SPECIAL, DIRECT, INDIRECT, CONSEQUENTIAL, INCIDENTAL, OR OTHER DAMAGES RESULTING FROM THE USE OF OR INABILITY TO USE SOFTWARE.

Article 3. Restrictions

You shall not, or shall not have any third party, reverse-engineer, decompile, or disassemble FIRMWARE.

DownloadFile name: FWUP0020.DAT / File size: 47.77MB

Caution

*Make sure there isn’t any file with the same name in the destination of the firmware to save. If there is a file with the same name, the browser may automatically alter the name of the firmware like the name and (1). A camera will not recognize the firmware correctly with an altered name like that.

Firmware compatibility table

  • Please use your camera and lens with the latest version of firmware. If you don’t use them with the latest version, you may not enjoy their full performance. Check the compatibility table below.
CamerasLenses